Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
What're your thoughts on How to Install a Bathtub Yourself?
Mounting a tub isn't exactly brain surgery, but it does require solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a new one is likewise a moderately difficult project. If the old bathtub is readily easily accessible, the job can relocate quickly; if you need to open a wall to remove the old tub as well as place the new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will require a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also fit trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly aid you install a brand-new bathtub in your washroom if you have actually already purchased a new bathtub as well as do not need to change the plan of your previous water pipes.
Your devices and also material list need to make up the following:
Preparing for the Installation
First of all, the supporting structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited gain access to that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the bathtub in the needed position. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little points.
The next goal is to make certain that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the tub up until the level checks out level.
To mount faucets, fit all-time low of the furthest flexible faucet port to the proper supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the supply of water as well as check all joints as well as brand-new pipework for leakages and also tighten them if required. Load the tub as well as also examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the bath tub should wait up until the tub has actually been used at the very least when as this will settle it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Secure the faucet in position with the manufacturer provided backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former kind ought to be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, causing difficulties with dampness and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can split rather very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Installing A Bathtub? Give a short review below. We would be glad to know your feelings about this write up. Hoping that you come back again before long. Make sure you take a moment to distribute this article if you appreciated it. Thanks for going through it.
Act now! Save later. Report this page